User Tools

Site Tools


lbaops:lbamay2005:v185a

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
lbaops:lbamay2005:v185a [2005/05/09 14:56]
jlovell
lbaops:lbamay2005:v185a [2015/12/18 16:38] (current)
Line 1: Line 1:
-===== v185a Setup:\\ ===== +===== v185a Setup: ===== 
-==== **(note additional config for ATCA in comments section below)**\\ ====+==== **(note additional config for ATCA in comments section below)** ==== 
 + 
 +^Antennas ​          | At-Mp-Ho-Cd-Pa-Hh | 
 +^Start ​             | 139 06:​30:​00 ​  | 
 +^Stop               | 139 18:​29:​10 ​  | 
 +^Channel 1          | 8417 - 8433 MHz USB RCP  | 
 +^Channel 2          | 8417 - 8433 MHz USB LCP  | 
 +^Bandwidth ​         | 16 MHz         | 
 +^Recorder ​          | S2             | 
 +^S2 Mode            | 32x4-2 ​        | 
 +^DAS Mode           | [[http://​www.atnf.csiro.au/​vlbi/​dasmodes/​16-1IF-2p-a.html|at16s.pro]] | 
 +^Buggary Cable      | in             | 
 +^Tape Change ​       | 139 12:​27:​08 ​  | 
 + 
 +Ftp: [[ftp://​ftp.atnf.csiro.au/​pub/​people/​vlbi/​v185/​v185a]] 
 +---- 
 + 
 +===== Comments: ===== 
 + 
 +Steven (during setup): have switched to DAS1 so that we can use full_64_64-128 correlator configuration to get 128 MHz with full stokes at 4800 MHz on ATCA 1freq. ​ 2freq set to 64 MHz band, but only two pol products xx and yy. 
 + 
 +Alternatively use S2 mode 32a4-2 without buggary cable. 
 +Either edit .skd file before running drudg, or edit .prc file 
 +after running drudge. 
 + 
 +PCFS schedules ftp'd and drudg'​d at At, Mp, Pa. 
 + 
 +**//Note for ATCA Observers://​** PI requests second frequency chain at ATCA to be set up with freq=4800 MHz,  
 +bandwidth=128 `MHz and that the ATCA finishes the schedule 15-20 minutes early (or continues observing past the end of 
 +recording) to make a 10 minute scan of 1934-638 for flux scale calibration. This will permit an accurate total flux density measurement and allow an ATCA image to be made at 4.8 and 8.4 GHz.
  
-^Antennas ​          | At-Mp-Ho-Cd-Pa-Hh |\\ 
-^Start ​             | 139 06:​30:​00 ​  |\\ 
-^Stop               | 139 18:​29:​10 ​  |\\ 
-^Channel 1          | 8417 - 8433 MHz USB RCP  |\\ 
-^Channel 2          | 8417 - 8433 MHz USB LCP  |\\ 
-^Bandwidth ​         | 16 MHz         |\\ 
-^Recorder ​          | S2             |\\ 
-^S2 Mode            | 32x4-2 ​        |\\ 
-^DAS Mode           | [[http://​www.atnf.csiro.au/​vlbi/​dasmodes/​16-1IF-2p-a.html|at16s.pro]] |\\ 
-^Buggary Cable      | in             |\\ 
-^Tape Change ​       | 139 12:​27:​08 ​  |\\ 
-\\ 
-Ftp: [[ftp://​ftp.atnf.csiro.au/​pub/​people/​vlbi/​v185/​v185a]]\\ 
-----\\ 
-\\ 
-===== Comments:\\ ===== 
-\\ 
-Alternatively use S2 mode 32a4-2 without buggary cable.\\ 
-Either edit .skd file before running drudg, or edit .prc file\\ 
-after running drudge\ 
-\ 
-**//Note for ATCA Observers://​** PI requests second frequency chain at ATCA to be set up with freq=4800 MHz, \\ 
-bandwidth=128 `MHz and that the ATCA finishes the schedule 15-20 minutes early (or continues observing past the end of\\ 
-recoding) to make a 10 minute scan of 1934-638 for flux scale calibration. This will permit an accurate total flux density measurement and allow an ATCA image to be made at 4.8 and 8.4 GHz. 
lbaops/lbamay2005/v185a.txt · Last modified: 2015/12/18 16:38 (external edit)