User Tools

Site Tools


lbaops:lbamay2006:v188atidnotes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
lbaops:lbamay2006:v188atidnotes [2006/05/11 11:07]
jlovell
lbaops:lbamay2006:v188atidnotes [2015/12/18 16:38] (current)
Line 1: Line 1:
-====== Tidbinbilla notes for V188a\\ ====== +====== Tidbinbilla notes for V188a ====== 
-\\ + 
-=====  Config notes\\ ===== +=====  Config notes ===== 
-  *  Centre freq = 2285 MHz\\ +  *  Centre freq = 2285 MHz 
-  *  Polarisation = RCP->​IFP1,​ LCP-IFP2\\ +  *  Polarisation = RCP->​IFP1,​ LCP-IFP2 
-  *  1st LO = 2000 MHz\\ +  *  1st LO = 2000 MHz 
-  *  mix to 160 MHz into DAS\\ +  *  mix to 160 MHz into DAS 
-  *  so 2nd LO for USB mix = 2285 - 2000 + 160 = 445 MHz\\ +  *  so 2nd LO for USB mix = 2285 - 2000 + 160 = 445 MHz 
-  *  DAS profile = vsop_f.pro\\ +  *  DAS profile = vsop_f.pro 
-  *  receiver configs:\\ +  *  receiver configs: 
-    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1\\ +    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1 
-    *  DCC2: LCP -> LNA1 (high noise diplexed path) -> out (output 2 for SNT monitoring). So '​SLDA1O2\\ +    *  DCC2: LCP -> LNA1 (high noise diplexed path) -> out (output 2 for SNT monitoring). So '​SLDA1O2 
-\\ + 
-=====  SOE\\ ===== +=====  SOE ===== 
-====  Before the track\\ ==== +====  Before the track ==== 
-  *  Tapes\\ +  *  Tapes 
-    *  get labels\\ +    *  get labels 
-    *  load first set\\ +    *  load first set 
-  *  Block 0 rack config\\ +  *  Block 0 rack config 
-    *  RCP -> IF1\\ +    *  RCP -> IF1 
-    *  LCP -> IF2\\ +    *  LCP -> IF2 
-    *  2nd LOs 1 and 2 to 445 MHz\\ +    *  2nd LOs 1 and 2 to 445 MHz 
-  *  PCFS\\ +  *  PCFS 
-    *  sched files\\ +    *  sched files 
-      *  fix timing\\ +      *  fix timing 
-      *  add source commands\\ +      *  add source commands 
-    *  modify PRC file\\ +    *  modify PRC file 
-      *  ND control\\ +      *  ND control 
-        *  copy calon, caloff, toload, tosky from ndtest.prc\\ +        *  copy calon, caloff, toload, tosky from v185bti (edit for correct NMC) 
-      *  VFC patching\\ +      *  VFC patching 
-        *  patch in S-band and set LOs to 272 MHz\\ +        *  patch in S-band and set LOs to 272 MHz 
-      *  S2 config\\ +      *  S2 config 
-  *  start DAS software\\ +  *  start DAS software 
-    *  configuration ti16s_f.pro\\ +    *  configuration ti16s_f.pro 
-    *  adjust attenuators\\ +    *  adjust attenuators 
-  *  tidvsi\\ +  *  tidvsi 
-    *  203.5.58.205\\ +    *  203.5.58.205 ​ ​(admin LAN only, use jplvisitor account) 
-    *  check time\\ +    *  check time 
-    *  vsib_record -m 3 -c xxxx -e /dev/vsib -t 32400s -o /​data/​removable/​v188a/​v188a-ti\\ +    *  vsib_record -m 3 -c xxxx -e /dev/vsib -t 32400s -o /​data/​removable/​v188a/​v188a-ti 
-      *  configure and start\\ +      *  configure and start 
-  *  xplot\\ +  *  xplot 
-    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40\\ +    *  on pcfs40: /​usr2/​st/​vlbisrv/​start_vlbisrv dflt 
-  *  start PCFS software\\ +    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40 
-    *  ssh ops@pcfs40\\ +  *  start PCFS software 
-    *  pcfsa-remote\\ +    *  ssh ops@pcfs40 
-      *  S2, S-RCP, S-LCP, maintenance\\ +    *  pcfsa-remote 
-    *  start the schedule\\ +      *  S2, S-RCP, S-LCP, maintenance 
-    *  configure VFCs with ifds and vclba\\ +    *  start the schedule 
-====  At start of track\\ ==== +    *  configure VFCs with ifds and vclba 
-  *  NMC\\ +====  At start of track ==== 
-    *  Link\\ +  *  NMC 
-      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers.\\ +    *  Link 
-    *  antenna startup\\ +      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers. 
-      *  in NMC:CTRL Connection Control:\\ +    *  antenna startup 
-        *  AP D TRK  (to show the track display)\\ +      *  in NMC:CTRL Connection Control: 
-          *  Check for:\\ +        *  AP D TRK  (to show the track display) 
-          * * delut ~ +229 ms\\ +          *  Check for: 
-          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively\\ +          * * delut ~ +229 ms 
-        *  ap band s\\ +          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively 
-        *  ap move r=240\\ +        *  ap band s 
-        *  ap semn 3spig.ac1\ +        *  ap move r=240 
-        *  ap semn 3scib.sem\\ +        *  ap semn 3spig.ac2 
-        *  ap radec 217.08656 -42.13415  (1424-418)\ +        *  ap semn 3scib.sem 
-        *  ap mode ac1\ +        *  ap radec  9.63649 -24.94850  (j0038-24
-        *  ap d sts (check all green. click on antenna to see brakes status)\\ +        *  ap mode ac2 
-        *  ap trk (start the antenna)\\ +        *  ap d sts (check all green. click on antenna to see brakes status) 
-        *  (make safety page)\\ +        *  ap trk (start the antenna) 
-        *  ap resm trk\\ +        *  (make safety page) 
-    *  start three connection blocks\\ +        *  ap resm trk 
-      *  connection blocks -> NDcontrol (Note PID)\\ +    *  start three connection blocks 
-      *  connection blocks -> UWVcontrol (Note PID)\\ +      *  connection blocks -> NDcontrol (Note PID) 
-      *  connection blocks -> APCcontrol (Note PID)\\ +      *  connection blocks -> UWVcontrol (Note PID) 
-    *  start the E-log TDN\\ +      *  connection blocks -> APCcontrol (Note PID) 
-      *  TDNs -> ** log? **\\ +    *  start the E-log TDN 
-      *  move to '​logs'​ workspace\\ +      *  TDNs -> ** log? ** 
-    *  receiver config\\ +      *  move to '​logs'​ workspace 
-        *  us d smap\\ +    *  receiver config 
-        *  us d xmap\\ +        *  us d smap 
-        *  (double-click on dichroic to move it IN)\\ +        *  us d xmap 
-        *  (configure with double-clicks)\\ +        *  (double-click on dichroic to move it IN) 
-        *  D1 D CNF 3\\ +        *  (configure with double-clicks) 
-        *  (select S band and [apply])\\ +        *  D1 D CNF 3 
-        *  if fails, try SC 99\\ +        *  (select ​SC 99 and S band and [apply]) 
-        *  make carrier 2280 MHz\\ +        *  make carrier 2280 MHz 
-        *  if fail to pick up correct LNA:\\ +        *  if fail to pick up correct LNA: 
-          *  D1 set uwv reset\\ +          *  D1 set uwv reset 
-          *  d1 set uwv srla2o2\\ +          *  d1 set uwv srla2o2 
-        *  D2 D CNF 4\\ +        *  D2 D CNF 4 
-        *  (select S band and [apply])\\ +        *  (select ​SC 99 and S band and [apply]) 
-        *  if fails, try SC 99\\ +        *  make carrier 2280 MHz 
-        *  make carrier 2280 MHz\\ +        *  if fail to pick up correct LNA: 
-        *  if fail to pick up correct LNA:\\ +          *  select connection "​none"​ 
-          *  select connection "​none"​\\ +          *  select connection DSS43SO2 
-          *  select connection DSS43SO2\\ +        *  if still failing 
-        *  if still failing\\ +          *  D1 set uwv reset 
-          *  D1 set uwv reset\\ +          *  d1 set uwv srla2o2 
-          *  d1 set uwv srla2o2\\ +        *  configure noise diode 
-        *  configure noise diode\\ +          *  d1 d prf 3 and d2 d prf 4 
-          *  d1 d prf 3 and d2 d prf 4\\ +          *  click on REC button in CNF windows 
-          *  click on REC button in CNF windows\\ +          *  select 12.5K and frequency = on, apply 
-          *  select 12.5K and frequency = on, apply\\ +          *  then enable/​disable, check in each IF 
-          *  then enable/​disable\\ +          *  to modulate 
-          *  to modulate\\ +          * * 0.25 K, 20 Hz, 5s, enable 
-          * * 0.25 K, 20 Hz, 5s, enable\\ +          *  repeat for D2 
-          *  repeat for D2\\ + 
-\\ +  *  boresight 
-  *  boresight\\ +    *  manual offsets e.g: 
-    *  manual offsets e.g:\\ +      *  ap po xel 0.1 
-      *  ap po xel 0.1\\ +  *  PCFS 
-  *  PCFS\\ +    *  check atten levels 
-    *  check atten levels\\ +
-\\+
  
  
lbaops/lbamay2006/v188atidnotes.txt · Last modified: 2015/12/18 16:38 (external edit)