User Tools

Site Tools


lbaops:xraidinstallandtest

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
lbaops:xraidinstallandtest [2007/01/29 12:23]
chris.phillips
lbaops:xraidinstallandtest [2015/12/18 16:39] (current)
Line 1: Line 1:
-===== Installing a set of Apple Xraid disks\\ ===== +===== Installing a set of Apple Xraid disks ===== 
-\\ + 
-  *  The PC does not need to be shutdown to swap/​install Xraid disks. However you need to be sure none of the disks you are removing are currently mounted. Check this with\\ +  *  The PC does not need to be shutdown to swap/​install Xraid disks. However you need to be sure none of the disks you are removing are currently mounted. Check this with 
-->  ''>​ df''​\\ +->  ''>​ df''​ 
--> If any /​data/​xraidN disks are present unmount them\\ +-> If any /​data/​xraidN disks are present unmount them 
-->  ''>​ umount /​data/​xraidN''​\\ +->  ''>​ umount /​data/​xraidN''​ 
-->See the troubleshooting guide if you cannot unmount the disk - alternatively just shut the machine down (but this is not recommended).\\ +->See the troubleshooting guide if you cannot unmount the disk - alternatively just shut the machine down (but this is not recommended). 
-\\ + 
-  *  Turn off the Xraid power. Do this either using the power switch at the rear (hold it down for a few seconds until it starts flashing) or using the Apple rail tools java gui.\\ +  *  Turn off the Xraid power. Do this either using the power switch at the rear (hold it down for a few seconds until it starts flashing) or using the Apple raid tools java gui. 
-\\ + 
-  *  Remove any current disks - give the front panel a gentle push and a handle will pop out allowing you to pull the disks out.\\ +  *  Remove any current disks - give the front panel a gentle push and a handle will pop out allowing you to pull the disks out. 
-\\ + 
-  *  Insert the disks by pushing each disk in firmly.\\ +  *  Insert the disks by pushing each disk in firmly. 
-\\ + 
--> **//NOTE**: It is possible the Xraid chassis is locked and needs to be unlocked before disks can be removed/​inserted. Don't use too much pressure! ​\\ +-> **//NOTE**: It is possible the Xraid chassis is locked and needs to be unlocked before disks can be removed/​inserted. Don't use too much pressure!  
-\\ + 
-  *  Once the disks are all inserted, give each disk another firm push to be sure it is sitting properly. Failure to do this may cause the Xraid to think there has been a disk failure and spend the next 24hours "​fixing"​ the volume. The best technique is to tap the front panel to get the handle to extend then give it a firm push in.\\ +  *  Once the disks are all inserted, give each disk another firm push to be sure it is sitting properly. Failure to do this may cause the Xraid to think there has been a disk failure and spend the next 24hours "​fixing"​ the volume. The best technique is to tap the front panel to get the handle to extend then give it a firm push in. 
-\\ + 
-  *  Turn the power back on to the Xraid using either the power switch or java gui.\\ +  *  Turn the power back on to the Xraid using either the power switch or java gui. 
-\\ + 
-  *  Once the Xraid is power up (check the lights on the front look OK) try and mount the disks\\ +  *  Once the Xraid is power up (check the lights on the front look OK) try and mount the disks 
--> ''>​ mount /​data/​xraid0''​\\ +-> ''>​ mount /​data/​xraid0''​ 
--> (etc). It is possible not all devices are detected (particularly if the PC is rebooted) see [[.:xxxxx]]\ +-> (etc). ​ 
-\ +->It is possible not all devices are detected (particularly if the PC is rebooted) see [[.:lbadrhints]] 
-  *  The permission on the mounted filesystem may be wrong (permission denied when you try and write to the disks). Fix this my logging on as root and:\\ + 
--> ''>​ chown vlbi:vlbi /​data/​xraid0''​\\ +  *  The permission on the mounted filesystem may be wrong (permission denied when you try and write to the disks). Fix this my logging on as root and: 
-->for each disk\\ +-> ''>​ chown vlbi:vlbi /​data/​xraid0''​ 
-\\ +->for each disk 
-  *  Test the disks performance using ''​diskspeed'':​\\ + 
--> ''>​ cd /​data/​xraid0''​\\ +  *  Test the disks performance using ''​diskspeed'':​ 
--> ''>​ diskspeed -n 5''​\\ +-> ''>​ cd /​data/​xraid0''​ 
--> The speed should be ~600 Mbps\\ +-> ''>​ diskspeed -n 5''​ 
-\\+-> The speed should be ~600 Mbps 
  
  
lbaops/xraidinstallandtest.txt · Last modified: 2015/12/18 16:39 (external edit)