User Tools

Site Tools


lbaops:lbamar2006:v185btidnotes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

lbaops:lbamar2006:v185btidnotes [2006/03/22 09:28]
jlovell
lbaops:lbamar2006:v185btidnotes [2006/03/22 11:45]
guest
Line 1: Line 1:
-====== Tidbinbilla notes for V185b\\ ====== +====== Tidbinbilla notes for V185b\ ====== 
-\+
-=====  Config notes\\ ===== +=====  Config notes\ ===== 
-  *  Centre freq = 2280 MHz\+  *  Centre freq = 2280 MHz\ 
-  *  Polarisation = RCP (IF1), LCP (IF2)\+  *  Polarisation = RCP (IF1), LCP (IF2)\ 
-  *  1st LO = 2000 MHz\+  *  1st LO = 2000 MHz\ 
-  *  mix to 160 MHz into DAS\+  *  mix to 160 MHz into DAS\ 
-  *  so 2nd LO for USB mix = 2280 - 2000 + 160 = 440 MHz\+  *  so 2nd LO for USB mix = 2280 - 2000 + 160 = 440 MHz\ 
-  *  DAS profile = ti16s_f.pro\+  *  DAS profile = ti16s_f.pro\ 
-  *  receiver configs:\+  *  receiver configs:\ 
-    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1\+    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1\ 
-    *  DCC2: LCP -> LNA1 (high noise path) -> out\+    *  DCC2: LCP -> LNA1 (high noise diplexed ​path) -> out (output 2 for SNT monitoring). So '​SLDA1O2'​\ 
 +
 +=====  SOE\ ===== 
 +====  Before the track\ ==== 
 +  *  Tapes\ 
 +    *  get labels\ 
 +    *  load first set\ 
 +  *  Block 0 rack config\ 
 +    *  RCP -> IF1\ 
 +    *  LCP -> IF2\ 
 +    *  2nd LOs 1 and 2 to 440 MHz\ 
 +  *  PCFS\ 
 +    *  sched files\ 
 +      *  fix timing\ 
 +      *  add source commands\ 
 +    *  modify PRC file\ 
 +      *  ND control\ 
 +        *  copy calon, caloff, toload, tosky from ndtest.prc\ 
 +      *  VFC patching\ 
 +        *  patch in S-band and set LOs to 272 MHz\ 
 +      *  S2 config\ 
 +  *  start DAS software\ 
 +    *  configuration ti16s_f.pro\ 
 +    *  adjust attenuators\ 
 +  *  telnet s2\ 
 +    *  check time\ 
 +  *  tidvsi\ 
 +    *  203.5.58.205\ 
 +    *  check time\ 
 +    *  start disko\ 
 +      *  configure and start\ 
 +  *  xplot\ 
 +    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40\ 
 +  *  start PCFS software\ 
 +    *  ssh ops@pcfs40\ 
 +    *  pcfsa-remote\ 
 +      *  S2, S-RCP, S-LCP, maintenance\ 
 +    *  start the schedule\ 
 +    *  configure VFCs with ifds and vclba\ 
 +====  At start of track\ ==== 
 +  *  NMC\ 
 +    *  Link\ 
 +      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers.\ 
 +    *  antenna startup\ 
 +      *  in NMC:CTRL Connection Control:\ 
 +        *  AP D TRK  (to show the track display)\ 
 +          *  Check for:\ 
 +          * * delut ~ +291 ms\ 
 +          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively\ 
 +        *  ap band s\ 
 +        *  ap move r=240\ 
 +        *  ap semn 3spig.ac1\ 
 +        *  ap semn 3scib.sem\ 
 +        *  ap radec 217.08656 -42.13415 ​ (1424-418)\ 
 +        *  ap mode ac1\ 
 +        *  ap d sts (check all green. click on antenna to see brakes status)\ 
 +        *  ap trk (start the antenna)\ 
 +        *  (make safety page)\ 
 +        *  ap resm trk\ 
 +    *  start three connection blocks\ 
 +      *  connection blocks -> NDcontrol (Note PID)\ 
 +      *  connection blocks -> UWVcontrol (Note PID)\ 
 +      *  connection blocks -> APCcontrol (Note PID)\ 
 +    *  start the E-log TDN\ 
 +      *  TDNs -> ** log? **\ 
 +      *  move to '​logs'​ workspace\ 
 +    *  receiver config\ 
 +        *  us d smap\ 
 +        *  us d xmap\ 
 +        *  (double-click on dichroic to move it IN)\ 
 +        *  (configure with double-clicks)\ 
 +        *  D1 D CNF 3\ 
 +        *  (select S band and [apply])\ 
 +        *  if fails, try SC 99\ 
 +        *  make carrier 2280 MHz\ 
 +        *  if fail to pick up correct LNA:\ 
 +          *  D1 set uwv reset\ 
 +          *  d1 set uwv srla2o2\ 
 +        *  D2 D CNF 4\ 
 +        *  (select S band and [apply])\ 
 +        *  if fails, try SC 99\ 
 +        *  make carrier 2280 MHz\ 
 +        *  if fail to pick up correct LNA:\ 
 +          *  select connection "​none"​\ 
 +          *  select connection DSS43SO2\ 
 +        *  if still failing\ 
 +          *  D1 set uwv reset\ 
 +          *  d1 set uwv srla2o2\ 
 +        *  configure noise diode\ 
 +          *  d1 d prf 3 and d2 d prf 4\ 
 +          *  click on REC button in CNF windows\ 
 +          *  select 12.5K and frequency = on, apply\ 
 +          *  then enable/​disable\ 
 +          *  to modulate\ 
 +          * * 0.25 K, 20 Hz, 5s, enable\ 
 +          *  repeat for D2\ 
 +
 +  *  boresight\ 
 +    *  manual offsets e.g:\ 
 +      *  ap po xel 0.1\ 
 +  *  PCFS\ 
 +    *  check atten levels\
 \ \
-=====  SOE\\ ===== 
-====  Before the track\\ ==== 
-  *  Tapes\\ 
-    *  get labels\\ 
-    *  load first set\\ 
-  *  Block 0 rack config\\ 
-    *  RCP -> IF1\\ 
-    *  LCP -> IF2\\ 
-    *  2nd LOs 1 and 2 to 440 MHz\\ 
-  *  PCFS\\ 
-    *  sched files\\ 
-      *  fix timing\\ 
-      *  add source commands\\ 
-    *  modify PRC file\\ 
-      *  ND control\\ 
-        *  copy calon, caloff, toload, tosky from ndtest.prc\\ 
-      *  VFC patching\\ 
-        *  patch in S-band and set LOs to 272 MHz\\ 
-      *  S2 config\\ 
-  *  start DAS software\\ 
-    *  configuration ti16s_f.pro\\ 
-    *  adjust attenuators\\ 
-  *  telnet s2\\ 
-    *  check time\\ 
-  *  tidvsi\\ 
-    *  203.5.58.205\\ 
-    *  check time\\ 
-    *  start disko\\ 
-      *  configure and start\\ 
-  *  xplot\\ 
-    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40\\ 
-  *  start PCFS software\\ 
-    *  ssh ops@pcfs40\\ 
-    *  pcfsa-remote\\ 
-      *  S2, S-RCP, S-LCP, maintenance\\ 
-    *  start the schedule\\ 
-    *  configure VFCs with ifds and vclba\\ 
-====  At start of track\\ ==== 
-  *  NMC\\ 
-    *  Link\\ 
-      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers.\\ 
-    *  antenna startup\\ 
-      *  in NMC:CTRL Connection Control:\\ 
-        *  AP D TRK  (to show the track display)\\ 
-          *  Check for:\\ 
-          * * delut ~ +291 ms\\ 
-          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively\\ 
-        *  ap band s\\ 
-        *  ap move r=240\\ 
-        *  ap semn 3spig.ac1\\ 
-        *  ap semn 3scib.sem\\ 
-        *  ap radec 217.08656 -42.13415 ​ (1424-418)\\ 
-        *  ap mode ac1\\ 
-        *  ap d sts (check all green. click on antenna to see brakes status)\\ 
-        *  ap trk (start the antenna)\\ 
-        *  (make safety page)\\ 
-        *  ap resm trk\\ 
-    *  start various blocks\ 
-      *  connection blocks -> NDcontrol (Note PID)\\ 
-      *  connection blocks -> UWVcontrol (Note PID)\\ 
-      *  connection blocks -> ** what goes here?**\ 
-    *  receiver config\\ 
-        *  us d smap\\ 
-        *  us d xmap\\ 
-        *  (double-click on dichroic to move it IN)\\ 
-        *  (configure with double-clicks)\\ 
-        *  D1 D CNF\ 
-        *  (select S band and [apply])\\ 
-        *  if fails, try SC 99\\ 
-        *  make carrier 2280 MHz\\ 
-        *  if fail to pick up correct LNA:\\ 
-          *  D1 set uwv reset\\ 
-          *  d1 set uwv srla2o2\\ 
-        *  D2 D CNF\ 
-          *  ** what goes here?**\ 
-        *  configure noise diode\\ 
-          *  d1 d prf\ 
-          *  click on REC button in CNF window\ 
-          *  select 12.5K and frequency = on, apply\\ 
-          *  then enable/​disable\\ 
-          *  to modulate\\ 
-          * * 0.25 K, 20 Hz, 5s, enable\\ 
-          *  repeat for D2\\ 
-\\ 
-  *  boresight\\ 
-    *  manual offsets e.g:\\ 
-      *  ap po xel 0.1\\ 
-  *  PCFS\\ 
-    *  check atten levels\\ 
-\\ 
  
  
lbaops/lbamar2006/v185btidnotes.txt · Last modified: 2015/12/18 16:38 (external edit)