User Tools

Site Tools


lbaops:lbamar2006:v185btidnotes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
lbaops:lbamar2006:v185btidnotes [2006/03/22 11:45]
guest
lbaops:lbamar2006:v185btidnotes [2015/12/18 16:38] (current)
Line 1: Line 1:
-====== Tidbinbilla notes for V185b====== +====== Tidbinbilla notes for V185b ====== 
-\ + 
-=====  Config notes===== +=====  Config notes ===== 
-  *  Centre freq = 2280 MHz\ +  *  Centre freq = 2280 MHz 
-  *  Polarisation = RCP (IF1), LCP (IF2)\ +  *  Polarisation = RCP (IF1), LCP (IF2) 
-  *  1st LO = 2000 MHz\ +  *  1st LO = 2000 MHz 
-  *  mix to 160 MHz into DAS\ +  *  mix to 160 MHz into DAS 
-  *  so 2nd LO for USB mix = 2280 - 2000 + 160 = 440 MHz\ +  *  so 2nd LO for USB mix = 2280 - 2000 + 160 = 440 MHz 
-  *  DAS profile = ti16s_f.pro\ +  *  DAS profile = ti16s_f.pro 
-  *  receiver configs:\ +  *  receiver configs: 
-    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1\ +    *  DCC1: RCP -> LNA2 (low noise path) -> out (output 1 for SNT monitoring). So `SRLA2O1 
-    *  DCC2: LCP -> LNA1 (high noise diplexed path) -> out (output 2 for SNT monitoring). So '​SLDA1O2'​\ +    *  DCC2: LCP -> LNA1 (high noise diplexed path) -> out (output 2 for SNT monitoring). So '​SLDA1O2'​ 
-\ + 
-=====  SOE===== +=====  SOE ===== 
-====  Before the track==== +====  Before the track ==== 
-  *  Tapes\ +  *  Tapes 
-    *  get labels\ +    *  get labels 
-    *  load first set\ +    *  load first set 
-  *  Block 0 rack config\ +  *  Block 0 rack config 
-    *  RCP -> IF1\ +    *  RCP -> IF1 
-    *  LCP -> IF2\ +    *  LCP -> IF2 
-    *  2nd LOs 1 and 2 to 440 MHz\ +    *  2nd LOs 1 and 2 to 440 MHz 
-  *  PCFS\ +  *  PCFS 
-    *  sched files\ +    *  sched files 
-      *  fix timing\ +      *  fix timing 
-      *  add source commands\ +      *  add source commands 
-    *  modify PRC file\ +    *  modify PRC file 
-      *  ND control\ +      *  ND control 
-        *  copy calon, caloff, toload, tosky from ndtest.prc\ +        *  copy calon, caloff, toload, tosky from ndtest.prc 
-      *  VFC patching\ +      *  VFC patching 
-        *  patch in S-band and set LOs to 272 MHz\ +        *  patch in S-band and set LOs to 272 MHz 
-      *  S2 config\ +      *  S2 config 
-  *  start DAS software\ +  *  start DAS software 
-    *  configuration ti16s_f.pro\ +    *  configuration ti16s_f.pro 
-    *  adjust attenuators\ +    *  adjust attenuators 
-  *  telnet s2\ +  *  telnet s2 
-    *  check time\ +    *  check time 
-  *  tidvsi\ +  *  tidvsi 
-    *  203.5.58.205\ +    *  203.5.58.205 
-    *  check time\ +    *  check time 
-    *  start disko\ +    *  start disko 
-      *  configure and start\ +    *  tunnel ports 7420 and 7426 to pentane.ssi.swin.edu.au via venice 
-  *  xplot\ +      *  configure and start 
-    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40\ +  *  xplot 
-  *  start PCFS software\ +    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40 
-    *  ssh ops@pcfs40\ +  *  start PCFS software 
-    *  pcfsa-remote\ +    *  ssh ops@pcfs40 
-      *  S2, S-RCP, S-LCP, maintenance\ +    *  pcfsa-remote 
-    *  start the schedule\ +      *  S2, S-RCP, S-LCP, maintenance 
-    *  configure VFCs with ifds and vclba\ +    *  start the schedule 
-====  At start of track==== +    *  configure VFCs with ifds and vclba 
-  *  NMC\ +====  At start of track ==== 
-    *  Link\ +  *  NMC 
-      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers.\ +    *  Link 
-    *  antenna startup\ +      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers. 
-      *  in NMC:CTRL Connection Control:\ +    *  antenna startup 
-        *  AP D TRK  (to show the track display)\ +      *  in NMC:CTRL Connection Control: 
-          *  Check for:\ +        *  AP D TRK  (to show the track display) 
-          * * delut ~ +291 ms\ +          *  Check for: 
-          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively\ +          * * delut ~ +291 ms 
-        *  ap band s\ +          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively 
-        *  ap move r=240\ +        *  ap band s 
-        *  ap semn 3spig.ac1\ +        *  ap move r=240 
-        *  ap semn 3scib.sem\ +        *  ap semn 3spig.ac1 
-        *  ap radec 217.08656 -42.13415 ​ (1424-418)\ +        *  ap semn 3scib.sem 
-        *  ap mode ac1\ +        *  ap radec 217.08656 -42.13415 ​ (1424-418) 
-        *  ap d sts (check all green. click on antenna to see brakes status)\ +        *  ap mode ac1 
-        *  ap trk (start the antenna)\ +        *  ap d sts (check all green. click on antenna to see brakes status) 
-        *  (make safety page)\ +        *  ap trk (start the antenna) 
-        *  ap resm trk\ +        *  (make safety page) 
-    *  start three connection blocks\ +        *  ap resm trk 
-      *  connection blocks -> NDcontrol (Note PID)\ +    *  start three connection blocks 
-      *  connection blocks -> UWVcontrol (Note PID)\ +      *  connection blocks -> NDcontrol (Note PID) 
-      *  connection blocks -> APCcontrol (Note PID)\ +      *  connection blocks -> UWVcontrol (Note PID) 
-    *  start the E-log TDN\ +      *  connection blocks -> APCcontrol (Note PID) 
-      *  TDNs -> ** log? **\ +    *  start the E-log TDN 
-      *  move to '​logs'​ workspace\ +      *  TDNs -> ** log? ** 
-    *  receiver config\ +      *  move to '​logs'​ workspace 
-        *  us d smap\ +    *  receiver config 
-        *  us d xmap\ +        *  us d smap 
-        *  (double-click on dichroic to move it IN)\ +        *  us d xmap 
-        *  (configure with double-clicks)\ +        *  (double-click on dichroic to move it IN) 
-        *  D1 D CNF 3\ +        *  (configure with double-clicks) 
-        *  (select S band and [apply])\ +        *  D1 D CNF 3 
-        *  if fails, try SC 99\ +        *  (select S band and [apply]) 
-        *  make carrier 2280 MHz\ +        *  if fails, try SC 99 
-        *  if fail to pick up correct LNA:\ +        *  make carrier 2280 MHz 
-          *  D1 set uwv reset\ +        *  if fail to pick up correct LNA: 
-          *  d1 set uwv srla2o2\ +          *  D1 set uwv reset 
-        *  D2 D CNF 4\ +          *  d1 set uwv srla2o2 
-        *  (select S band and [apply])\ +        *  D2 D CNF 4 
-        *  if fails, try SC 99\ +        *  (select S band and [apply]) 
-        *  make carrier 2280 MHz\ +        *  if fails, try SC 99 
-        *  if fail to pick up correct LNA:\ +        *  make carrier 2280 MHz 
-          *  select connection "​none"​\ +        *  if fail to pick up correct LNA: 
-          *  select connection DSS43SO2\ +          *  select connection "​none"​ 
-        *  if still failing\ +          *  select connection DSS43SO2 
-          *  D1 set uwv reset\ +        *  if still failing 
-          *  d1 set uwv srla2o2\ +          *  D1 set uwv reset 
-        *  configure noise diode\ +          *  d1 set uwv srla2o2 
-          *  d1 d prf 3 and d2 d prf 4\ +        *  configure noise diode 
-          *  click on REC button in CNF windows\ +          *  d1 d prf 3 and d2 d prf 4 
-          *  select 12.5K and frequency = on, apply\ +          *  click on REC button in CNF windows 
-          *  then enable/​disable\ +          *  select 12.5K and frequency = on, apply 
-          *  to modulate\ +          *  then enable/​disable 
-          * * 0.25 K, 20 Hz, 5s, enable\ +          *  to modulate 
-          *  repeat for D2\ +          * * 0.25 K, 20 Hz, 5s, enable 
-\ +          *  repeat for D2 
-  *  boresight\ + 
-    *  manual offsets e.g:\ +  *  boresight 
-      *  ap po xel 0.1\ +    *  manual offsets e.g: 
-  *  PCFS\ +      *  ap po xel 0.1 
-    *  check atten levels\ +  *  PCFS 
-\+    *  check atten levels 
  
  
lbaops/lbamar2006/v185btidnotes.1142988331.txt.gz · Last modified: 2015/12/18 16:38 (external edit)