lbaops:lbanov2005:vt02e1
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
lbaops:lbanov2005:vt02e1 [2005/10/26 13:24] chris.phillips |
lbaops:lbanov2005:vt02e1 [2015/12/18 16:38] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== vt02e1 Setup:\\ ===== | + | ===== vt02e1 Setup: ===== |
| - | ^Antennas | Pa-At-Mp-Ho-Cd |\ | + | ^Antennas | Pa-At-Mp-Cd | |
| - | ^Start | 304 22:00:00 |\\ | + | ^Start | 304 22:00:00 | |
| - | ^Stop | 306 04:00:00 |\\ | + | ^Stop | 306 04:00:00 | |
| - | ^Channel 1 | 8417 - 8433 MHz USB RCP |\\ | + | ^Channel 1 | 8417 - 8433 MHz USB RCP | |
| - | ^Channel 2 | 8417 - 8433 MHz USB LCP |\\ | + | ^Channel 2 | 8417 - 8433 MHz USB LCP | |
| - | ^Bandwidth | 16 MHz |\\ | + | ^Bandwidth | 16 MHz | |
| - | ^Recorder | Disk through S2 |\\ | + | ^Recorder | Disk through S2 | |
| - | ^DAS Mode | [[http://www.atnf.csiro.au/vlbi/dasmodes/16-1IF-2p-a.html|at16s.pro]] |\\ | + | ^DAS Mode | [[http://www.atnf.csiro.au/vlbi/dasmodes/16-1IF-2p-a.html|at16s.pro]] | |
| - | ^S2 Mode | 32x4-2 |\\ | + | ^S2 Mode | 32x4-2 | |
| - | ^Buggary Cable | in |\\ | + | ^Buggary Cable | in | |
| - | \\ | + | |
| - | Ftp: [[ftp://ftp.atnf.csiro.au/pub/people/vlbi/vt02/vt02e1]]\\ | + | Ftp: [[ftp://ftp.atnf.csiro.au/pub/people/vlbi/vt02/vt02e1]] |
| - | ----\\ | + | ---- |
| - | \\ | + | |
| - | ===== Comments:\\ ===== | + | ===== Comments: ===== |
| - | \\ | + | |
| - | Setup and fringe check for v131ba. Please email vlbiobs when you are setup and tracking.\\ | + | Setup and fringe check for v131ba. Please email vlbiobs when you are setup and tracking. |
| - | \\ | + | |
| - | Alternatively use S2 mode 32a4-2 without buggary cable.\\ | + | Source coordinates are: |
| - | Either edit .skd file before running drudg, or edit .prc file\\ | + | |
| + | 16h17m49.276394s -77d17'18.46754" (J2000) | ||
| + | |||
| + | Alternatively use S2 mode 32a4-2 without buggary cable. | ||
| + | Either edit .skd file before running drudg, or edit .prc file | ||
| after running drudge | after running drudge | ||
| + | |||
| + | The VSIC should be connected to the S2 C2a output via the BG2 cable. vsib record should be run in a directory something like: | ||
| + | vsib_record -t 6h -o vt02e1-Pa -c ooxx # If using buggary cable | ||
| + | vsib_record -t 6h -o vt02e1-Pa -c oxox # No buggary and S2 mode 32a4-2 | ||
| + | |||
| + | Remember to enable "uic feedthru on" on the S2 | ||
| + | |||
lbaops/lbanov2005/vt02e1.txt · Last modified: 2015/12/18 16:38 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
