User Tools

Site Tools


lbaops:lbanov2006:v189atilog

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
lbaops:lbanov2006:v189atilog [2006/11/14 12:56]
jlovell
lbaops:lbanov2006:v189atilog [2015/12/18 16:38] (current)
Line 1: Line 1:
-The data for v189a should be recorded to the first of the new sets of xraids (7 x 500 GB)\\ +The data for v189a should be recorded to the first of the new sets of xraids (7 x 500 GB) 
-\\ + 
---\\ +Data being recorded to first set of Xraid disks as labeled: /​data/​xraid0. Interestingly this is the right-hand bank of disks. 
-\\ + 
-====== Tidbinbilla Setup notes for V189a\\ ====== +Data recorded as follows: 
-\\ + 
-=====  Config notes\\ ===== + ​09:​50:​00 -> 09:​50:​30 ​  - duration was set to 30s, whoops! 
-  *  Centre freqs = 1650, 1682 MHz MHz\\ + ​09:​58:​00 -> 10:​27:​12 ​  ​Stopped to reconfigure caching settings on the Xraids 
-  *  Polarisation = LCP\\ + ​10:​28:​00 -> end 
-  *  1st LO = 1380 MHz\\ + 
-  *  mix to 160 MHz into DAS\\ +Notes: 
-  *  so 2nd LO for USB mix \\ + ​09:​50:​00 ​  On point and recording 
-    *  IFP1: 1650 - 1380 + 160 = 430 MHz\\ + ​12:​28:​00 ​  ​(approx time) IF2 unplugged briefly for a sanity check 
-    *  IFP1: 1682 - 1380 + 160 = 462 MHz\\ + ​12:​37:​00 ​  ​Antenna off point for ~ 30s for another sanity check 
-  *  DAS profile = vsop_f.pro\\ + ​12:​42:​00 ​  After conversation with Adam, can see no problems with the  
-\\ +            system so suspect lack of fringes to Tid is due to checking  
-\\ +            software not handling the mixture of bands and pols correctly.  
-=====  SOE\\ ===== +            Have double checked frequency setup, antenna pointing, recorder 
-====  Before the track\\ ==== +            clock etc and all looks correct. 
-  *  Block 0 rack config\\ + 
-    *  Split L-band signal then amplify, attennuate, mix etc to IFP1, 2\\ + 
-    *  2nd LOs\\ +---- 
-      *  1: 430 MHz\\ + 
-      *  2: 462 MHz\\ +====== Tidbinbilla Setup notes for V189a ====== 
-  *  PCFS\\ + 
-    *  sched files\\ +=====  Config notes ===== 
-      *  fix timing\\ +  *  Centre freqs = 1650, 1682 MHz MHz 
-      *  add source commands\\ +  *  Polarisation = LCP 
-    *  modify PRC file\\ +  *  1st LO = 1380 MHz 
-      *  VFC patching\\ +  *  mix to 160 MHz into DAS 
-        *  patch in L-band and set LOs to 286 MHz (1666 MHz Sky)\\ +  *  so 2nd LO for USB mix  
-      *  S2 config\\ +    *  IFP1: 1650 - 1380 + 160 = 430 MHz 
-  *  start DAS software\\ +    *  IFP1: 1682 - 1380 + 160 = 462 MHz 
-    *  configuration vsop_f.pro\\ +  *  DAS profile = vsop_f.pro 
-    *  adjust attenuators\\ + 
-  *  tidvsi\\ + 
-    *  203.5.58.205 ​ (admin LAN only, use jplvisitor account)\\ +=====  SOE ===== 
-    *  check time\\ +====  Before the track ==== 
-    *  use disko\\ +  *  Block 0 rack config 
-    *  vsib_record -m 3 -c xxxx -e /dev/vsib -t 32400s -o /​blah/​v189a-ti\\ +    *  Split L-band signal then amplify, attennuate, mix etc to IFP1, 2 
-      *  configure and start\\ +    *  2nd LOs 
-  *  xplot\\ +      *  1: 430 MHz 
-    *  on pcfs40: /​usr2/​st/​vlbisrv/​start_vlbisrv dflt\\ +      *  2: 462 MHz 
-    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40\\ +  *  PCFS 
-  *  start PCFS software\\ +    *  sched files 
-    *  ssh ops@pcfs40\\ +      *  fix timing 
-    *  pcfsa-remote\\ +      *  add source commands 
-      *  S2, S-RCP, S-LCP, maintenance\\ +    *  modify PRC file 
-    *  start the schedule\\ +      *  VFC patching 
-    *  configure VFCs with ifds and vclba\\ +        *  patch in L-band and set LOs to 286 MHz (1666 MHz Sky) 
-====  At start of track\\ ==== +      *  S2 config 
-  *  NMC\\ +  *  start DAS software 
-    *  Link\\ +    *  configuration vsop_f.pro 
-      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers.\\ +    *  adjust attenuators 
-    *  antenna startup\\ +  *  tidvsi 
-      *  in NMC:CTRL Connection Control:\\ +    *  203.5.58.205 ​ (admin LAN only, use jplvisitor account) 
-        *  AP D TRK  (to show the track display)\\ +    *  check time 
-          *  Check for:\\ +    *  use disko 
-          * * delut ~ +229 ms\\ +    *  vsib_record -m 3 -c xxxx -e /dev/vsib -t 32400s -o /​blah/​v189a-ti 
-          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively\\ +      *  configure and start 
-        *  ap band s\\ +  *  xplot 
-        *  ap move r=240\\ +    *  on pcfs40: /​usr2/​st/​vlbisrv/​start_vlbisrv dflt 
-        *  ap semn 3spig.ac2\\ +    *  on eac40: /​opt/​rmc/​bin/​xplot -rh pcfs40 
-        *  ap semn 3scib.sem\\ +  *  start PCFS software 
-        *  ap radec  9.63649 -24.94850 ​ (j0038-24)\\ +    *  ssh ops@pcfs40 
-        *  ap mode ac2\\ +    *  pcfsa-remote 
-        *  ap d sts (check all green. click on antenna to see brakes status)\\ +      *  S2, S-RCP, S-LCP, maintenance 
-        *  ap trk (start the antenna)\\ +    *  start the schedule 
-        *  (make safety page)\\ +    *  configure VFCs with ifds and vclba 
-        *  ap resm trk\\ +====  At start of track ==== 
-    *  start three connection blocks\\ +  *  NMC 
-      *  connection blocks -> NDcontrol (Note PID)\\ +    *  Link 
-      *  connection blocks -> UWVcontrol (Note PID)\\ +      *  Build link with antenna and receiver, spacecraft 50 (VLBI), pass 0, two receivers. 
-      *  connection blocks -> APCcontrol (Note PID)\\ +    *  antenna startup 
-    *  start the E-log TDN\\ +      *  in NMC:CTRL Connection Control: 
-      *  TDNs -> ** log? **\\ +        *  AP D TRK  (to show the track display) 
-      *  move to '​logs'​ workspace\\ +          *  Check for: 
-    *  receiver config\\ +          * * delut ~ +229 ms 
-        *  us d smap\\ +          * * models for encoder and position should be 3SPIG.AC1 and 3SCIB.SEM respectively 
-        *  us d xmap\\ +        *  ap band s 
-        *  (double-click on dichroic to move it IN)\\ +        *  ap move r=240 
-        *  (configure with double-clicks)\\ +        *  ap semn 3spig.ac2 
-        *  D1 D CNF 3\\ +        *  ap semn 3scib.sem 
-        *  (select SC 99 and S band and [apply])\\ +        *  ap radec  9.63649 -24.94850 ​ (j0038-24) 
-        *  make carrier 2280 MHz\\ +        *  ap mode ac2 
-        *  if fail to pick up correct LNA:\\ +        *  ap d sts (check all green. click on antenna to see brakes status) 
-          *  D1 set uwv reset\\ +        *  ap trk (start the antenna) 
-          *  d1 set uwv srla2o2\\ +        *  (make safety page) 
-        *  D2 D CNF 4\\ +        *  ap resm trk 
-        *  (select SC 99 and S band and [apply])\\ +    *  start three connection blocks 
-        *  make carrier 2280 MHz\\ +      *  connection blocks -> NDcontrol (Note PID) 
-        *  if fail to pick up correct LNA:\\ +      *  connection blocks -> UWVcontrol (Note PID) 
-          *  select connection "​none"​\\ +      *  connection blocks -> APCcontrol (Note PID) 
-          *  select connection DSS43SO2\\ +    *  start the E-log TDN 
-        *  if still failing\\ +      *  TDNs -> ** log? ** 
-          *  D1 set uwv reset\\ +      *  move to '​logs'​ workspace 
-          *  d1 set uwv srla2o2\\ +    *  receiver config 
-        *  configure noise diode\\ +        *  us d smap 
-          *  d1 d prf 3 and d2 d prf 4\\ +        *  us d xmap 
-          *  click on REC button in CNF windows\\ +        *  (double-click on dichroic to move it IN) 
-          *  select 12.5K and frequency = on, apply\\ +        *  (configure with double-clicks) 
-          *  then enable/​disable,​ check in each IF\\ +        *  D1 D CNF 3 
-          *  to modulate\\ +        *  (select SC 99 and S band and [apply]) 
-          * * 0.25 K, 20 Hz, 5s, enable\\ +        *  make carrier 2280 MHz 
-          *  repeat for D2\\ +        *  if fail to pick up correct LNA: 
-\\ +          *  D1 set uwv reset 
-  *  boresight\\ +          *  d1 set uwv srla2o2 
-    *  manual offsets e.g:\\ +        *  D2 D CNF 4 
-      *  ap po xel 0.1\\ +        *  (select SC 99 and S band and [apply]) 
-  *  PCFS\\ +        *  make carrier 2280 MHz 
-    *  check atten levels\\ +        *  if fail to pick up correct LNA: 
-\\ +          *  select connection "​none"​ 
-\\ +          *  select connection DSS43SO2 
-  *  schedule file changes\\ +        *  if still failing 
-remove all:\\ +          *  D1 set uwv reset 
-st=\\ +          *  d1 set uwv srla2o2 
-et\\ +        *  configure noise diode 
-unlod\\ +          *  d1 d prf 3 and d2 d prf 4 
-setup0*\\ +          *  click on REC button in CNF windows 
-ready\\ +          *  select 12.5K and frequency = on, apply 
-tape\\ +          *  then enable/​disable,​ check in each IF 
-\\ +          *  to modulate 
-Add to prc file:\\ +          * * 0.25 K, 20 Hz, 5s, enable 
-\\ +          *  repeat for D2 
- ​define ​ ifds          06132201809x ​           ​\\ + 
- ​ifd=,,​nor,​nor ​\\ +  *  boresight 
- ​lo=lo1,​1380,​usb,​lcp,​1.0,​0 ​\\ +    *  manual offsets e.g: 
- ​patch=lo1,​1h,​2h,​3h,​4h,​5h,​6h,​7h,​8h,​9h,​10h,​11h,​12h,​13h,​14h ​\\ +      *  ap po xel 0.1 
- ​enddef\\ +  *  PCFS 
- ​define ​ vclba         ​06132201825x ​           ​\\ +    *  check atten levels 
- ​vc01=285.99,​16.00,​ul\\ + 
- ​vc02=285.99,​16.00,​ul\\ + 
- ​vc03=285.99,​16.00,​ul\\ +  *  schedule file changes 
- ​vc04=285.99,​16.00,​ul\\ +remove all: 
- ​vc05=285.99,​16.00,​ul\\ +st= 
- ​vc06=285.99,​16.00,​ul\\ +et 
- ​vc07=285.99,​16.00,​ul\\ +unlod 
- ​vc08=285.99,​16.00,​ul  ​\\ +setup0* 
- ​vc09=285.99,​16.00,​ul  ​\\ +ready 
- ​vc10=285.99,​16.00,​ul  ​\\ +tape 
- ​vc11=285.99,​16.00,​ul  ​\\ + 
- ​vc12=285.99,​16.00,​ul  ​\\ +Add to prc file: 
- ​vc13=285.99,​16.00,​ul  ​\\ + 
- ​vc14=285.99,​16.00,​ul  ​\\ + ​define ​ ifds          06132201809x ​            
- !+1s\\ + ​ifd=,,​nor,​nor  
- ​valarm\\ + ​lo=lo1,​1380,​usb,​lcp,​1.0,​0  
- ​enddef\\ + ​patch=lo1,​1h,​2h,​3h,​4h,​5h,​6h,​7h,​8h,​9h,​10h,​11h,​12h,​13h,​14h  
- ​define ​ postob ​       00000000000x\\ + ​enddef 
- ​enddef\\ + ​define ​ vclba         ​06132201825x ​            
- ​define ​ sched_end ​    ​00000000000x ​           ​\\ + ​vc01=285.99,​16.00,​ul 
- ​sy=echo "​QUIT"​ | netcat nmc-ws4 -q 2 6543\\ + ​vc02=285.99,​16.00,​ul 
- ​sy=echo "​QUIT"​ | netcat nmc-ws4 -q 2 6643\\ + ​vc03=285.99,​16.00,​ul 
- ​sy=echo "​TERMINATE"​ | netcat nmc-ws4 -q 2 6743\\ + ​vc04=285.99,​16.00,​ul 
- ​enddef\\ + ​vc05=285.99,​16.00,​ul 
- \\ + ​vc06=285.99,​16.00,​ul 
- \\ + ​vc07=285.99,​16.00,​ul 
-\\ + ​vc08=285.99,​16.00,​ul ​  
-\\ + ​vc09=285.99,​16.00,​ul ​  
-\\+ ​vc10=285.99,​16.00,​ul ​  
 + ​vc11=285.99,​16.00,​ul ​  
 + ​vc12=285.99,​16.00,​ul ​  
 + ​vc13=285.99,​16.00,​ul ​  
 + ​vc14=285.99,​16.00,​ul ​  
 + ​!+1s 
 + ​valarm 
 + ​enddef 
 + ​define ​ postob ​       00000000000x 
 + ​enddef 
 + ​define ​ sched_end ​    ​00000000000x ​            
 + ​sy=echo "​QUIT"​ | netcat nmc-ws4 -q 2 6543 
 + ​sy=echo "​QUIT"​ | netcat nmc-ws4 -q 2 6643 
 + ​sy=echo "​TERMINATE"​ | netcat nmc-ws4 -q 2 6743 
 + ​enddef 
 +  
 +  
 + 
 + 
  
  
lbaops/lbanov2006/v189atilog.txt · Last modified: 2015/12/18 16:38 (external edit)